H3.X Lightweight IMA Computer

For data concentrator and battery or fuel cell management applications

At a glance

Architecture
Single channel
Mass
250 g
Power
8 W maximum
Isolation
Non-isolated
RTOS
ARINC 653 Part 1
H3.X Computer — interactive 3D model

Drag to rotate, scroll to zoom

The H3.X Computer completes the family as a highly optimized, ultra-lightweight single-channel computer for auxiliary and distributed systems.

Key capabilities

  • Distributed architectures: engineered for data concentrators and battery, fuel cell, and powertrain control and prognostic health management.
  • End system safety: capable of supporting safety-critical functions from upstream to downstream processing.
  • Optimized for auxiliary applications: the H3.X omits galvanic isolation, allowing a significant reduction in Bill of Materials (BoM) cost where the installation does not require it.
  • Ultra-low Size, Weight, and Power (SWaP): where quantity and SWaP sensitivity are high, but compromising reliability and safety is not an option.

System integration

In a distributed avionics architecture, the H3.X is a smart data concentrator. It collects high-frequency sensor readings, such as battery cell or fuel cell data, and transmits them over the aircraft network.

Modular platform

The H-series IMA computers are modular by design and share the same Hover Real-Time Operating System (H-RTOS) and Hover Software Development Kit (H-SDK). The H3.X is compatible with every H-series main processing board, including the safety-critical and edge inference boards.

Specifications

Physical

4 items
Dimensions110 × 60 × 30 mm
Mass250 g
CoolingConduction-cooled, no forced air
MountingThree-point flange, dedicated grounding point

Electrical

5 items
Input voltage18.0 V to 32.2 V DC steady state
Nominal voltage28 V DC
Power consumption6.4 W typical, 8 W maximum
Galvanic isolationNon-isolated, optimized for size, weight, and cost
ConnectorsModular, high-reliability EN4165

Processing

4 items

H3.0

Main processing boardSafety-critical
Processors2 × Arm Cortex-A72 @ 800 MHz
Memory and storage16 GB SDRAM and 1 GB NOR flash
Design assuranceDAL A

H3.1

Main processing boardEdge inference
Processors2 × Arm Cortex-A76 @ 1.8 GHz and 2 × Arm Cortex-A55 @ 1.5 GHz
Memory and storageOn-board eMMC
Design assuranceDAL C

Environmental qualification (RTCA DO-160G)

15 items
4.5 Temperature / 4.6 AltitudeCategory D2
5. Temperature variationCategory B
6. HumidityCategory B
7.2 Operational shock / 7.3 Crash safetyCategory E
8. VibrationCategory U
10. WaterproofnessCategory W
12. Sand and dustCategory S
16. Power inputCategories B and Z (2.5 ms power interruption)
17. Voltage spikeCategory A
19. Induced signal susceptibilityCategory ZN
20. RF susceptibilityRadiated Y, conducted R
21. RF emissionsCategories H and Q
22. Lightning-induced transient susceptibilityB3K3L3
25. Electrostatic dischargeCategory A
26. Fire, flammabilityCategory C

Specifications are typical values and subject to change. Contact us for the controlled datasheet before committing to a design.

Interfaces

  • Ethernet

    2 × 1 GbE, IEEE 802.1 TSN

  • CAN FD / isoSPI

    Configurable on the fly: 4 CAN FD, or 2 CAN FD plus 4 isoSPI

  • EIA-485

    1, half-duplex, 50 Mbps

  • Analog inputs

    8

  • General-purpose I/O

    1 input / 5 outputs

  • Power

    1 × 28 V input and ground

Interface availability and channel counts vary by configuration. Full pin-level detail is provided in the Interface Control Document.

Design assurance and qualification

  • RTCA DO-160G environmental qualification
  • RTCA DO-178C Level A (software)
  • RTCA DO-254 Level A (complex hardware)
  • RTCA DO-297 Integrated Modular Avionics (IMA) guidance
  • TSO-C153a IMA platform authorization

Typical applications

  • Battery management
  • Data concentrator
  • Fuel cell management
  • Powertrain controller

Inside the H3.X

H3.X Computer exploded into its parts

Request the full datasheet

Our engineering team can provide the complete datasheet, 3D Computer-Aided Design (CAD) STEP models, and the electrical and mechanical Interface Control Document (ICD) under a Non-Disclosure Agreement (NDA).

Other computers in the family

Designing a certifiable aircraft?

Summarize your requirements, including SWaP budget and certifiable aircraft type. Our engineering team will contact you shortly.