H1.X Dual-Channel IMA Computer

For applications that require redundancy

At a glance

Architecture
Dual channel
Mass
650 g
Power
20 W maximum
Isolation
Galvanically isolated
RTOS
ARINC 653 Part 1
H1.X Computer — interactive 3D model

Drag to rotate, scroll to zoom

The H1.X Computer is our flagship dual-channel computer, built for the airworthiness demands of crewed and uncrewed aircraft.

Key capabilities

  • Dual-channel redundancy: two fully independent channels, with separate power supplies and processing, mitigate single-point failures.
  • Galvanic isolation: isolated interfaces protect the computer from electromagnetic noise and voltage spikes across aircraft buses.
  • Safety monitoring: an independent challenge-response watchdog continuously monitors computational integrity.

System integration

The ARINC 653 partitioned Real-Time Operating System (RTOS) allows safety-critical and non-safety-critical software applications to share the Integrated Modular Avionics (IMA) platform with guaranteed spatial and temporal separation. The ARINC 615A data loader uploads/downloads software securely over the aircraft network while the unit remains installed.

Modular platform

The H-series IMA computers are modular by design and share the same Hover Real-Time Operating System (H-RTOS) and Hover Software Development Kit (H-SDK). The H1.X is compatible with every H-series main processing board, including the safety-critical and edge inference boards.

Specifications

Physical

4 items
Dimensions110 × 105 × 65 mm
Mass650 g
CoolingConduction-cooled, no forced air
MountingThree-point flange, dedicated grounding point

Electrical

5 items
Input voltage18.0 V to 32.2 V DC steady state
Nominal voltage28 V DC
Power consumption16 W typical, 20 W maximum
Galvanic isolationBetween channels and on all external interfaces
ConnectorsModular, high-reliability EN4165

Processing

4 items

H1.0 Channel A

Main processing boardSafety-critical
Processors2 × Arm Cortex-A72 @ 800 MHz
Memory and storage16 GB SDRAM, 1 TB NAND flash and 1 GB NOR flash
Design assuranceDAL A

H1.0 Channel B

Main processing boardSafety-critical
Processors2 × Arm Cortex-A72 @ 800 MHz
Memory and storage16 GB SDRAM, 1 TB NAND flash and 1 GB NOR flash
Design assuranceDAL A

H1.1 Channel A

Main processing boardSafety-critical
Processors2 × Arm Cortex-A72 @ 800 MHz
Memory and storage16 GB SDRAM, 1 TB NAND flash and 1 GB NOR flash
Design assuranceDAL A

H1.1 Channel B

Main processing boardEdge inference
Processors2 × Arm Cortex-A76 @ 1.8 GHz and 2 × Arm Cortex-A55 @ 1.5 GHz
Memory and storageOn-board eMMC
Design assuranceDAL C

Environmental qualification (RTCA DO-160G)

15 items
4.5 Temperature / 4.6 AltitudeCategory D2
5. Temperature variationCategory B
6. HumidityCategory B
7.2 Operational shock / 7.3 Crash safetyCategory E
8. VibrationCategory U
10. WaterproofnessCategory W
12. Sand and dustCategory S
16. Power inputCategories B and Z (2.5 ms power interruption)
17. Voltage spikeCategory A
19. Induced signal susceptibilityCategory ZN
20. RF susceptibilityRadiated Y, conducted R
21. RF emissionsCategories H and Q
22. Lightning-induced transient susceptibilityB3K3L3
25. Electrostatic dischargeCategory A
26. Fire, flammabilityCategory C

Specifications are typical values and subject to change. Contact us for the controlled datasheet before committing to a design.

Interfaces

  • Ethernet

    3 × 1 GbE per channel (6 total), IEEE 802.1 TSN

  • CAN FD

    2 per channel (4 total), 5 Mbps

  • EIA-485

    1 per channel (2 total), half-duplex, 50 Mbps

  • DisplayPort (5-bay version only)

    1 per channel (2 total), 5.4 Gbps

  • Analog inputs

    7 per channel (14 total)

  • General-purpose inputs

    3 per channel (6 total)

  • PWM outputs

    6 per channel (12 total)

  • Quadrature decoder

    2 per channel (4 total)

  • Power

    1 × 28 V input and ground per channel (2 total)

Interface availability and channel counts vary by configuration. Full pin-level detail is provided in the Interface Control Document.

Design assurance and qualification

  • RTCA DO-160G environmental qualification
  • RTCA DO-178C Level A (software)
  • RTCA DO-254 Level A (complex hardware)
  • RTCA DO-297 IMA guidance
  • TSO-C153a IMA platform authorization

Typical applications

  • Cockpit display computer
  • Flight computer
  • Powertrain and motor controller

Inside the H1.X

H1.X Computer exploded into its parts

Request the full datasheet

Our engineering team can provide the complete datasheet, 3D Computer-Aided Design (CAD) STEP models, and the electrical and mechanical Interface Control Document (ICD) under a Non-Disclosure Agreement (NDA).

Other computers in the family

Designing a certifiable aircraft?

Summarize your requirements, including SWaP budget and certifiable aircraft type. Our engineering team will contact you shortly.